| |
|
|
Tools, Stands, Ramps & Other Useful Things
Click the logo for Mechanix Wear Gloves
Fro Petrol Pressure Washer £255.00
Click on picture for larger image
Industrial high pressure jet wash. 1450psi rated pressure with maximimum of 2030psi. Flow rate of 8l per minute. 3600rpm. Unleaded petrol. 118cc engine. Low oil shut down. Low pressure detergent injection, temperature protect apparatus
Motion Pro Fork Bleeders £14.99
The quickest way to bleed off excess air in your forks.
No more messing around with screws that are determined
to lose themselves at the track or garage.
Suitable for most makes of bikes, state year, make and model of bike when ordering.
MotionPro Folding Sag Scale £22.99
Simple to use for measuring sag, an invaluable aid for setting up suspension.
* 6061-T6 aluminum construction
* Rigid folding design fits in most tool boxes
* Direct reading scale (no subtracting required)
* Adjustable zero set point with extended range
* Will work on mini and full size motorcycles
* Inch and metric scale combination
* Installs in rear axle
* Can be used to check front or rear sag
* Extended length 28 1/4 in.
* Folded length 15 3/4 in.
MotionPro Chain/Wheel Alignment Tool £17.99
Simple to use for true chain/wheel alignment, helps to reduce chain & sprocket wear
Motion Pro Bead Buddy £18.99 each
Take the labour out of changing tyres. The Bead Buddy is used to keep the tyre in the wheel well assisting with tyre fitting.
Ideal for trail, enduro and motocrossers, a necessity for those using Mitchelin "Mousses" instead of inner tubes.
A minimum of 3 are needed for fitting "Mousses".
Motion Pro Chain press Tool Kit £34.99
Fits 520-630 standard and "O"ring chains
Motion Pro Heavy Duty Chain Tool £96.99
Breaks and Rivets chains from 520 - 630
Motion Pro Chain Breaker and Rivet Tool Kit £66.99
Versatile enough to be used on cam chains or drive chains
Breaks chains from 350 to 630
Motion Pro Hydraulic Brake Bleeder £11.99
Make brake bleeding a one man job with this essential piece of kit
Motion Pro Cable Luber £6.99
Used to inject lubricants under pressure, such as WD40 into the cable sheath.
Sticky clutch and throttle cables are easily cured and it prolongs the life of the
cable at the same time if used each time after cleaning the bike.
Motion Pro Clutch Holding Tool £19.99
Having problems holding your clutch basket still for removal?
This tool holds the basket in one place whilst you get on with the job of loosening
the centre bolt.
Motion Pro Crankcase Splitter £139.99
Ever been tempted to use a hammer or screwdriver to split casings that refuse to budge?
This is what the pro's use to split most 2 and 4 stroke engine cases (vertically split types)
Motion Pro Degree Wheel £12.99
Accurately check or set ignition and or cam timing
Motion Pro Piston Pin Tool £44.99
A precision tool for removing and installing piston pins
Fits pistons from 40mm to 100mm and all pins from 12mm to 25mm
Motion Pro Compression Tester £109.99
Designed to check cylinder compression, quickly and easily
identify low compression causing that loss of power.
Includes hoses for 10, 12 and 14mm spark plug holes. Can be used on both 2 & 4 stroke engines.
Motion Pro 2 Stroke Leak Down Tester £199.99
Essential tool designed to check for damaging air leaks in 2-stroke engines
Includes air pressure gauge, pump up bulb and most fittings & adapters for single & twin cylinder 2-stroke engines
Packed in a convenient carry box, complete with instructions
Motion Pro 4-Stroke Leak Down Tester £119.99
Designed to test amount of cylinder leakage on 4 stroke engines
The gauge will register the total percentage of leakage past the rings,
head gasket, intake and exhaust valves
Motion Pro Ignition System Tester £6.99
For testing the integrity and strength of your ignition system
Motion Pro Fork Oil Level Gauge £19.99
Use to check and adjust oil levels on all conventional and inverted forks
Motion Pro Spring Hook (Heavy duty or standard)
Easily remove and re-fit exhaust, seat, tank and side stand springs
Motion Pro Swing Arm Bearing Tool £77.99
Designed for the installation of swing arm bearings on late Japanese motorcycles
Motion Pro Fork Seal Driver
Split design for ease of use, each driver weighs approx 25oz
----------------------------------
Workshop Clamp (Floor standing) £454.95
Floor Model with 60 pound base plate adjusts from 50 to 62 inches in height. Includes convenient cast aluminum tool tray with assorted compartments and slots for tools, lubes and small parts.
The perfect solution for holding any work item, from pistons and barrels to forks and frames.
Workshop Clamp (Bench Mounting) £249
* Perfectly suited to smaller workshops and garages
* No more dropped/scratched forks
* No matter what shape or size of suspension these clamps will fit
* Quick adjusting slide and locking system allows adjustment from 22 mm to 100 mm in a flash
* Clamping pressure is fully adjustable to avoid crushing stanchions or sliders
* Unique design allows the clamp to pivot 90 degrees and rotate 360 degrees for a perfect working position.
Aluminium Vice Insert £19.95
* The heavy duty AV-4 is a must-have tool for every mechanic's workbench
* A choice of three precision-machined openings allow you to grip axles and tighten the tool in a workbench vice
* Aluminium jaws prevent you from damaging ultra fine axle threads
* Bridge springs keep the jaws properly aligned and allow the tool to open automatically when the vice is opened
Bar and Frame Straightener £69.99
* A controlled way to straighten frames, forks, cranks, and handlebars, when feasible
* Nylon coated hook and fulcrum to prevent paint damage
* The hook has up to 8 inches of adjustment for ideal positioning
* Re-inforced and super stiff design resists flexing
* To be used with care, especially on high-end or thin-walled equipment
* Repairs must be carefully inspected for cracks or kinks and the item discarded if any found
Steering Race Press £139.99
* Eliminates damaged or misaligned bearing races
* Helps prevent dented and chipped frames
* Unique design permits quick tool installation and release after races are seated
* The heat-treated bushings provide a precise fit and alignment for most bikes
Steering Race Remover £29.99
The Park Tool Head Race Remover makes head tube bearing race removal easy. The tool is pulled through the steering tube until the flared ends snap in behind the race. A blow on the tool head removes the race. RT-2 fits most brands with 35–55 mm (1.1/2" - 2 3/16") bearing races.
Generally speaking, the RT-2 will fit most brands of larger motorcycles, (125cc's and up) both dirt bikes and street bikes and newer Harley Davidson's.
Crown Race Bearing Installer £69.99
The CRS-2M offers a new, safe approach to lower bearing installation. This unique system utilizes specially designed, aluminum inserts to quickly and accurately install nearly any lower bearing. Simply choose the correct insert, slide the setting driver over the steering tube and tap the bearing into place with a hammer, avoiding any risk of damage. The CRS-2M includes three specially shaped aluminum inserts (1”, 1-1/8” and 1-3/8”) and a heat-treated, universal setting driver.
Wheel Truing Stand £74.99
# The TS-7M is constructed from heavy gauge steel and allows for extremely accurate and reliable wheel truing at an economical price
# For wheels up to 180 mm wide and 740 mm in diameter
Nitrile Workshop Gloves £24.95
Park Tool Nitrile Gloves keep hands free of dirt, oil and potentially harmful chemicals and solvents. Thin enough to maintain dexterity, tough enough to resist snags. Sizes M, L, or XL (100 Gloves per box).
DRC Spoke Wrench £9.99
Interchangable tips to fit 8 sizes of spoke nipples.
Main shaft is CNC precision machined from 7075A aluminum, and designed for optimum grip.
Tips are made of heat treated steel for strength.
Available in six beautiful annodized colors. Tip Sizes: (5.4/5.6/5.8/6.0/6.2/6.4/6.6/6.8mm)
DRC Air Valve Puller £4.99
 
Makes it easy to pull the valve stem thru the hole in the rim, no more sore fingers!
DRC Mousse Changer £199.99
DRC HC2 Bike Stand £44.99
The best just got better. Using the same high quality components,
DRC have managed to refine and improve upon the original stand. The DRC2 stand now has a twin
spar lifting handle and the locking pin has been replaced with a hook non removable, so no more lost pins.
Of course the same superior features and quality of the original stand have been kept for the DRC2 stand.
DRC's kick up stand is height adjustable allowing it to be used with both low clearance bikes
like Supermoto's and higher motocross bikes.
If not locked in place, the top plate can be free moving
allowing you to swivel your bike around if garage space is at a premium.
This is a high quality Japanese product at an exceptional price.
----------------------------------
DRC Folding Bike or Quad Ramp £55.99
 
The DRC bike ramp is strong but light weight and because of the folding design
is very easy to store out of the way in the van, car, trailer or at home. 2 ramps used together
makes loading and unloading Quads and Atv's simplicity itself.
# Aluminium and nylon tube and plate construction
# Light weight construction
# 180cm/6 foot long
# 20cm/8 inches wide
# Foot caps for stability, made of ABS resin
# Tongue for fitting track bed
# Rubber plate under the tongue to prevent slippage
# 190kg/400lb capacity
# Ideal for bikes quads and atv's
Jack in the Box Kickup Bike Stand £29.99
Our budget stand at a really affordable price
----------------------------------
|
|
